Urgent Help need
Submitted by mikelee on Wed, 04/23/2008 - 7:41pm.
I had use Intel Mother board. DG33TL with Core2 Quad CPU, 4gb DDR2 RAM. and I use Sangoma A200D 8 port FXO with echo cancellation board. after installation I find there are two "kernal" at start up time
trixbox (2.6.18-53.1.4.el5PAE)
trixbox base (2.6.18-53.1.4.el5)
When I start with 2.6.18-53.1.4.el5PAE, it will stop at "Starting udev"
When I start with 2.6.18-53.1.4.el5, it will go through with almost everything except zaptel module. seems it loads zaptel module, then it find no function module.
after login with root ,
# ztcfg -vv
Zaptel Version: 1.4.9.2-
Echo Canceller: Oslec
Configuration
======================
Channel map:
0 channels to configure.
Can someone help me out, why there are two module why first module does not work ? can I saty with trixbox base module, and how can I make Sangoma card work?
Thanks a lot
did you install wanpipe and
Wed, 04/23/2008 - 7:46pm
did you install wanpipe and wanpipe-utils ?
Then run setup-sangoma?
ps dont run pae nothings built for it.....
I do not know what PAE stand
Wed, 04/23/2008 - 8:19pm
I do not know what PAE stand for. it come out to the 1st boot module. Can I edit it and remove it ?
Regarding Sangoma A200D, are you talking about this is right procedure to do setup for
http://wiki.sangoma.com/wanpipe-asterisk-trixbox-rpms
PAE explained @
Wed, 04/23/2008 - 8:41pm
PAE explained @ http://www.trixbox.org/wiki/kernel-PAE
As far as sangoma goes I only know the real general steps mentioned above you would actually need to get a Sangoma person/user to tell you if those directions are accurate....
Just want given back what I got.
Wed, 04/23/2008 - 9:06pm
After my fresh install, boot with trixbox base (2.6.18-53.1.4.el5)
Although I seems by pass every thing, but zaptel not loading. and it get loging prompt
where I keep getting " mpg31: Kill Process"
I just ignore it and login.
I followed this link http://wiki.sangoma.com/wanpipe-asterisk-trixbox-rpms
Here is what I do and finally seems get success, hope this log can help other beginners.
Again thanks for James point me ignore APE, module.
------------------------------------------------------------------------------------------------------
#cd /usr/src
#ls -l
total 10948
drwxr-xr-x 2 root root 4096 Mar 5 17:39 debug
lrwxrwxrwx 1 root root 22 Apr 23 23:40 freepbx -> /usr/src/freepbx-2.4.0
drwxr-xr-x 6 root root 4096 Apr 23 23:40 freepbx-2.4.0
-rw-r--r-- 1 root root 4504454 Apr 23 23:48 wanpipe-modules-2.6.18-53.1.4.el5-3.2.5-0.i686.rpm
-rw-r--r-- 1 root root 6656315 Apr 23 23:48 wanpipe-util-3.2.5-0.i686.rpm
[trixbox1.localdomain src]# rpm -i wanpipe-modules-2.6.18-53.1.4.el5-3.2.5-0.i686.rpm
Wanpipe Modules located in /lib/modules/2.6.18-53.1.4.el5
[trixbox1.localdomain src]# rpm -i wanpipe-util-3.2.5-0.i686.rpm
*** Sangoma Wanpipe was successfully installed.
Run wancfg command to configure wanpipe.
Refer to /usr/share/doc/wanpipe for documentation.
wanrouter hwprobe
-------------------------------
| Wanpipe Hardware Probe Info |
-------------------------------
1 . AFT-A200-SH : SLOT=0 : BUS=6 : IRQ=11 : CPU=A : PORT=PRI : HWEC=32 : V=11
Card Cnt: S508=0 S514X=0 S518=0 A101-2=0 A104=0 A300=0 A200=1 A108=0
# wanrouter hwprobe verbose
-----------------------------------------
| Wanpipe Hardware Probe Info (verbose) |
-----------------------------------------
1 . AFT-A200-SH : SLOT=0 : BUS=6 : IRQ=11 : CPU=A : PORT=PRI : HWEC=32 : V=11
+01:FXO:PCI
+02:FXO:PCI
+03:FXO:PCI
+04:FXO:PCI
+05:FXO:PCI
+06:FXO:PCI
+07:FXO:PCI
+08:FXO:PCI
+09:EMPTY
+10:EMPTY
+11:EMPTY
+12:EMPTY
+13:EMPTY
+14:EMPTY
+15:EMPTY
+16:EMPTY
+17:EMPTY
+18:EMPTY
+19:EMPTY
+20:EMPTY
+21:EMPTY
+22:EMPTY
+23:EMPTY
+24:EMPTY
Card Cnt: S508=0 S514X=0 S518=0 A101-2=0 A104=0 A300=0 A200=1 A108=0
#setup-sangoma
#############################################i##########################
# Sangoma Wanpipe: Zaptel/SMG/TDMAPI/BOOT Configuration Script #
# v2.10 #
# Sangoma Technologies Inc. #
# Copyright(c) 2007. #
########################################################################
Generating configuration files for Trixbox
---------------------------------------------
Configuring T1/E1 cards [A101/A102/A104/A108]
---------------------------------------------
------------------------------------
Configuring ISDN BRI cards [A500]
------------------------------------
No Sangoma ISDN BRI cards detected
Press any key to continue:
-----------------------------------------------------------
A200 detected on slot:0 bus:6
-----------------------------------------------------------
Which codec will be used?
1. MULAW - North America
2. ALAW - Europe
[1-2]:1
A200 configured on slot:0 bus:6 span:1
Press any key to continue:
Analog card configuration complete
###################################################################
# SUMMARY #
###################################################################
0 T1/E1 port(s) detected, 0 configured
0 ISDN BRI port(s) detected, 0 configured
1 analog card(s) detected, 1 configured
Configurator has created the following files:
1. Wanpipe config files in /etc/wanpipe
2. Zaptel config file /etc/zaptel.conf
3. Zapata config file /etc/asterisk/zapata-auto.conf
Your original configuration files will be saved to:
1. /etc/zaptel.conf.bak
2. /etc/asterisk/zapata-auto.conf.bak
Your configuration has been saved in /etc/wanpipe/debug-2008-04-23.tgz.
When requesting support, email this file to techdesk@sangoma.com
Zaptel and Wanpipe configuration complete: choose action
1. Save cfg: Restart Asterisk & Wanpipe now
2. Save cfg: Restart Asterisk & Wanpipe when convenient
3. Save cfg: Stop Asterisk & Wanpipe now
4. Save cfg: Stop Asterisk & Wanpipe when convenient
5. Do not save cfg: Exit
[1-5]:
STOPPING ASTERISK
Disconnected from Asterisk server
Asterisk Stopped
STOPPING FOP SERVER
FOP Server Stopped
Stopping Wanpipe...
Unloading Zaptel modules...
Removing old configuration files...
Copying new Wanpipe configuration files...
Copying new Zaptel configuration file (/etc/zaptel.conf)...
Copying new chan_zap configuration files (/etc/asterisk/zapata-auto.conf)...
Starting Wanpipe...
Starting WAN Router...
Loading WAN drivers: wanpipe done.
Starting up device: wanpipe1
--> Loading ec image OCT6116-64S.ima...
Configuring interfaces: w1g1
done.
Loading Zaptel...
Zaptel Version: 1.4.9.2
Echo Canceller: OSLEC
Configuration
======================
8 channels to configure.
Starting Amportal...
SETTING FILE PERMISSIONS
Permissions OK
STARTING ASTERISK
Asterisk is already running
STARTING FOP SERVER
FOP Server Started
Wanrouter start complete...
Current boot level is 3
Wanrouter boot scripts configuration...
Removing existing wanrouter boot scripts...OK
Would you like wanrouter to start on system boot?
1. YES
2. NO
[1-2]:1
Verifying Zaptel boot scripts...Enabled (level:09)
Verifying Zaptel shutdown scripts...Enabled (level:92)
Enabling wanrouter boot scripts ...(level:8)
Enabling wanrouter shutdown scripts ...(level:91)
Sangoma cards configuration complete, exiting...
# ztcfg -vv
Zaptel Version: 1.4.9.2
Echo Canceller: OSLEC
Configuration
======================
Channel map:
Channel 01: FXS Kewlstart (Default) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Slaves: 02)
Channel 03: FXS Kewlstart (Default) (Slaves: 03)
Channel 04: FXS Kewlstart (Default) (Slaves: 04)
Channel 05: FXS Kewlstart (Default) (Slaves: 05)
Channel 06: FXS Kewlstart (Default) (Slaves: 06)
Channel 07: FXS Kewlstart (Default) (Slaves: 07)
Channel 08: FXS Kewlstart (Default) (Slaves: 08)
8 channels to configure.
[trixbox1.localdomain ~]#
Member Since:
2006-11-06