r4fxo trixbox 2.2 kernel panic

All I know is that I have a r4fxo-ec. I am not sure what diver is in the package. I did contact tech support and am still waiting for a reply

Could it be I just have old firmware that doesn't work with the new drivers?

Hmm I got response and responded... Anywho here ya go

filename: /lib/modules/2.6.18-53.1.4.el5/misc/rcbfx/rcbfx.ko
license: GPL
version: 1.05
author: Bob Conklin
description: Rhino Equipment Modular Analog Interface Driver 1.05 09/21/07 (2.2.3)
alias: pci:v00000B0Bd00000706sv*sd*bc*sc*i*
alias: pci:v00000B0Bd00000906sv*sd*bc*sc*i*
alias: pci:v00000B0Bd00000506sv*sd*bc*sc*i*
alias: pci:v00000B0Bd00000406sv*sd*bc*sc*i*
alias: pci:v00000B0Bd00000206sv*sd*bc*sc*i*
depends:
vermagic: 2.6.18-53.1.4.el5 SMP mod_unload 686 REGPARM 4KSTACKS gcc-4.1
parm: force_fw:Reprogram firmware regardless of version (int)
parm: debug:1 for debugging messages (int)
parm: zt_ec_chanmap:int
parm: fxs_alg_chanmap:int
parm: fxo_alg_chanmap:int
parm: use_fxs_chanmap:int
parm: use_fxo_chanmap:int

----------------------------------------------

Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0743000 soft=c0723000
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 252572k/261752k available (2080k kernel code, 8620k reserved, 869k data, 220k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1325.12 BogoMIPS (lpj=662563)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f3ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 14k freed
CPU0: Intel Pentium III (Coppermine) stepping 03
Total of 1 processors activated (1325.12 BogoMIPS).
ExtINT not setup in hardware but reported by MP table
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=340 bytes
sizeof(dentry)=136 bytes
sizeof(ext3inode)=492 bytes
sizeof(buffer_head)=52 bytes
sizeof(skbuff)=172 bytes
checking if image is initramfs... it is
Freeing initrd memory: 2316k freed
NET: Registered protocol family 16
ACPI Exception (utmutex-0262): AE_BAD_PARAMETER, Thread C1263AA0 could not acquire Mutex [2] [20060707]
ACPI Exception (utmutex-0262): AE_BAD_PARAMETER, Thread C1263AA0 could not acquire Mutex [2] [20060707]
PCI: PCI BIOS revision 2.10 entry at 0xfc05e, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0880-08bf claimed by ICH4 GPIO
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Using IRQ router PIIX/ICH [8086/2410] at 0000:00:1f.0
PCI->APIC IRQ transform: 0000:00:1f.2[D] -> IRQ 185
PCI->APIC IRQ transform: 0000:00:1f.3[B] -> IRQ 169
PCI->APIC IRQ transform: 0000:00:1f.5[B] -> IRQ 169
PCI->APIC IRQ transform: 0000:01:00.0[A] -> IRQ 161
PCI->APIC IRQ transform: 0000:02:08.0[A] -> IRQ 169
PCI->APIC IRQ transform: 0000:02:0c.0[A] -> IRQ 177
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: fc000000-fdffffff
PREFETCH window: f4000000-f5ffffff
PCI: Bridge: 0000:00:1e.0
IO window: e000-efff
MEM window: fa000000-fbffffff
PREFETCH window: 20000000-200fffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
audit: initializing netlink socket (disabled)
audit(1205167171.084:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key EE0941287449EA77
- User ID: CentOS (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel i820 Chipset.
agpgart: AGP aperture is 64M @ 0xf0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH: IDE controller at PCI slot 0000:00:1f.1
ICH: chipset revision 2
ICH: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: Maxtor 6E040L0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: Lite-On LTN483S 48x Max, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(33)
hda: cache flushes supported
hda: hda1 hda2 hda3
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 220k freed
Write protecting the kernel read-only data: 388k
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
logips2pp: Detected unknown logitech mouse model 1
USB Universal Host Controller Interface driver v3.0
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: UHCI Host Controller
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.2: irq 185, io base 0x0000ff80
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
input: PS/2 Logitech Mouse as /class/input/input1
SCSI subsystem initialized
libata version 2.21 loaded.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1205167177.585:2): selinux=0 auid=4294967295
hdc: ATAPI 48X CD-ROM drive, 120kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:0c.0: 3Com PCI 3c905C Tornado at d083cc00.
input: PC Speaker as /class/input/input2
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 50851 usecs
intel8x0: clocking to 48000
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: ioctl: 4.11.0-ioctl (2006-09-14) initialised: dm-devel@redhat.com
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on hda2, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 779144k swap on /dev/hda3. Priority:-1 extents:1 across:779144k
IA-32 Microcode Update Driver: v1.14a
microcode: CPU0 updated from revision 0xc to 0x13, date = 02062001
Open Source Line Echo Canceller Installed
zaptel: no version for "oslec_echo_can_traintap" found: kernel tainted.
Zapata Telephony Interface Registered on major 196
Zaptel Version: 1.4.7-3259
Zaptap registered 'sample' char driver on major 33
Registered Tormenta2 PCI
usbcore: registered new driver wcusb
Wildcard USB FXS Interface driver registered
rcbfx 1: Rhino PCI BAR0 fafff000 IOMem mapped at d0942000
rcbfx 1: Waiting for response from card .........
rcbfx 1: Firmware Version 1.b
rcbfx 1: Firmware File Version is 1.b
rcbfx 1: Hardware version 11
rcbfx 1: G168 07 04 DSP Loader file size = 170 App file size = 48414
rcbfx 1: G168 DSP Ping DSP Version 106
rcbfx 1: G168 DSP Active and Servicing 4 Channels - f
rcbfx 1: Starting DMA
rcbfx 1: Spotted a Rhino: Rhino RCB4FXO (4 channels)
Registered tone zone 0 (United States / North America)
Registered tone zone 0 (United States / North America)
eth0: setting full-duplex.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
Zaptel Transcoder support loaded

I am no longer getting the Kernel Panic on 2.4.0. I installed the Rhino Telephony interface support in the package handler and then ran genzaptelconf. The trunks do not show up. Sorry for my lack of knowledge as it's been awhile since I worked with trixbox. This system has been rock solid until this past weekend.

Yum updates are not recommended. When updating your system you need to make sure that you update specific packages only....
You may want to try a reinstall or call our tech support so that we can try and help you further.